|
|
|||||
| From | Message |
| Mark S 8/28/2007 12:00:11 PM |
 Subject:
Nu Lustre 55Message: Hi, I a have poured my countertop twice and find that there are ridges/lines and or patches where the product has pooled....I am finding it tough to get a completely smooth surface....there are indeed areas that are perfectly smooth but many that are not......squeegee lines ....etc....Any ideas as to how to achieve a consistent finish? Would having a less glossy finish "mask" my poor pouring tecnique? Is there a product that I can put over Nu Lustre 55that would "dull" the finish an still be good for a kitchen countertop? Thanks very much, Mark |
| Mark 8/29/2007 7:18:19 AM |
RE: Nu Lustre 55 Message: The only reasons why Nu-Lustre might give you ridges or lines are: 1. The product had begun to cure in the mixing containers prior to pouring, or 2. A blower or hair dryer was used to try to eliminate bubbles. As long as you mix up enough Nu-Lustre and pour so that the Nu-Lustre flows over the entire surface, you will never have any ridges or lines. You can re-pour, ensuring the adequate epoxy is mixed and poured. You can sand the finish with sandpaper or steel wool if you want to have a less glossy finish. |
| raj 9/3/2007 8:35:53 PM |
RE: Nu Lustre 55 Message: how do you use Nu Lustre 55 on photos, and i want your phone number so i can contact you. |
| Mark 9/4/2007 6:11:40 AM |
RE: Nu Lustre 55 Message: Like any other application over paper, the surface should first be sealed to prevent the Nu-Lustre-55 from wetting the paper. A solution of watered down glue works very well. For contact information, click on www.swingpaints.com/a_contact_swing.htm |
| Neil 9/6/2007 10:10:38 PM |
RE: Nu Lustre 55 Message: You can also try laminating. Some varnished photos do not require sealing. |
| Anita 9/20/2007 9:16:54 AM |
RE: Nu Lustre 55 Message: I've had the same problem with Nu-Lustre-55 with pooling, etc. I'm totally not happy about it. It looks absolutely terrible. I did a table, and the first coat looked uneven, so i put a second coat on and it's even worse. Now what do i do? Totally unhappy with the product! |
| Neil 9/20/2007 10:09:18 PM |
RE: Nu Lustre 55 Message: Sound like you were not working on a level surface. This product will run to the lowest point. |
| Mark 9/21/2007 6:59:45 AM |
RE: Nu Lustre 55 Message: Anita, You have sent 2 e-mails describing what you call "high and low spots". If you do not apply an adequate amount of epoxy onto the surface, you will not achieve a uniform surface. Although you never gave any details about the table, did you clean it prior to applying the Nu-Lustre? This finish will not adhere properly to a surface that is waxed or polished. |
| Annie 9/28/2007 1:34:52 PM |
RE: Nu Lustre 55 Message: I'm thinking about using Nu-Lustre 55 on a kitchen island made out of walnut. Does anyone have anything good to say about this product? I'm afraid of trying it after reading the problems people had with the "pooling". I'd appreciate it if anyone can give me any GOOD feedback on this. Thanks, Annie |
| Mark 9/28/2007 1:42:43 PM |
RE: Nu Lustre 55 Message: The key to using this product is to become familiar with it by doing several small sample pieces. Pooling, stickiness, ridges are all avoided by people who read the entire set of instructions and follow them. |
| Annie 9/28/2007 1:46:06 PM |
RE: Nu Lustre 55 Message: Thanks for a quick response. Can you tell me where I can purchase Nu Luster 55 in Ottawa Ontario? I have checked with a few places and have not had any luck (one company gave me a 3 weeks delivery time). Thanks again, Annie |
| Mark 9/28/2007 2:07:18 PM |
RE: Nu Lustre 55 Message: In stock at European Paint & Glass on Bank Street. Not sure if Randall's carries the product or not. Home Depot in Nepean carried it in many sizes. |
| Annie 9/29/2007 8:32:12 AM |
RE: Nu Lustre 55 Message: Hi Mark, thank you for the information. I called a few Home Depot's and the South Keys location has the 4 litre for $110.00. None of the others carry it anymore. European Paint and Glass has it for $85.00. |
| Valerie Frocklage 10/1/2007 8:43:57 PM |
RE: Nu Lustre 55 Message: I have coated a drop leaf table with Nu-lustre 55 and am very pleased with the finish. I taped the leave/table edge and placed wax paper between the leaves and main table to ensure I would not have to much thickness between the leaves and main table. Now I have a ridge along the table seam slightly higher than the rest of the table. can I plane it off? If so how do I get the sheen back? Can I polish it? Should I have coated the entire surface and then sawed it apart? If this is the case I do have enough Nu Lustre 55 to do another coat. Should I plane off the ridge and then pour another coat over the entire table (leaves and all) and then saw through the leaf/table seam? If my idea of planeing is OK how do I finish the planed part? I could not find full detailed info on finishing, polishing etc. can you help? Please reply as soon as possible? thanks |
| Les 10/5/2007 7:48:39 AM |
RE: Nu Lustre 55 Message: I am about to us this product on a bar I am building in my basement and I don't if I can get it in a big enough size without spending a fortune. My bar countertops are 38 Sq ft in size. I will be covering coasters and beercaps as well as some ceramic tile. Can you give some advice as to using it on coasters , so as not to ruin them as well. Can I also us this product over wood with stain on it. What is the Largest size available and where in the Kitchener , Ontario area can I find it. As well can you give some advice as to how to not run into the same problems as your other customers when applying this product. Is it the same as commercial grade epoxy used in commercial flooring. Thanks Les |
| Mark 10/5/2007 8:21:29 AM |
RE: Nu Lustre 55 Message: Under no circumstances should you attempt to use this product on a bar without testing it on several different pieces. You want to be very familiar with it before tackling a large project. The best advice is to follow the detailed direction sheet. You can apply Nu-Lustre-55 onto stained wood. The product is avaible in 3.78L kits (about what you will need for your bar) and is available at Rona, Pro Hardware and TruServe Hardware. |
| Mark 10/5/2007 8:26:41 AM |
RE: Nu Lustre 55 Message: Valerie, You have posed a very interesting question, and one that I have never attempted. I guess that I might have gone about it by placing the wax paper vertically between the table and the leaves. I would then pour a uniform thickness over the entire table, including the leaves (can do the leaves at a separate time). You can certainly sand or plane off the excess epoxy. In order to obtain a sheen, you will need to polish the surface with successively finer grades of wet/dry sandpaper, and possibly even going as far as using pumice stone to achieve a high gloss. |
| Les 10/5/2007 9:17:24 AM |
RE: Nu Lustre 55 Message: Will I have any problems with using this over top of beer coasters and caps and how much working time will I have. For the size of my bar , what is the best way to make sure that there are no bubbles and or ridges and if so what would be the best way to get rid of them. |
| Mark 10/5/2007 10:11:49 AM |
RE: Nu Lustre 55 Message: Working time is over an hour and up to 4 hours, depending on temperature of mixture and temperature of room. Bubbles should be removed with a small butane or propane torch. Ridges form when there is not enough epoxy poured onto the surface. You should not encounter this problem if you pour on enough of the coating. |
| Les Moberg 10/5/2007 10:33:42 AM |
RE: Nu Lustre 55 Message: Will I have any problem with pouring over coasters or any kind of pictures. I see someone has asked about it before and you said to use a solution of watered down glue. |
| Les Moberg 10/5/2007 10:37:23 AM |
RE: Nu Lustre 55 Message: Will I have any problem with pouring over coasters or any kind of pictures. I see someone has asked about it before and you said to use a solution of watered down glue. |
| Les Moberg 10/5/2007 10:38:06 AM |
RE: Nu Lustre 55 Message: Will I have any problem with pouring over coasters or any kind of pictures. I see someone has asked about it before and you said to use a solution of watered down glue. |
| Mark 10/5/2007 10:53:52 AM |
RE: Nu Lustre 55 Message: I do not know why you would have any problems pouring over coasters. What are they made of? Any time you want to pour onto uncoated paper you will need to seal the surface of the epoxy will wet the paper and turn it transluscent. One way to seal the paper is with a dilute solution of white glue. |
| Les 10/5/2007 11:32:03 AM |
RE: Nu Lustre 55 Message: What would you class as uncoated paper. Would it workover pictures. How would someone apply the solution of white glue if it is needed. What type of white glue is needed as well. |
| Neil 10/7/2007 11:10:57 PM |
RE: Nu Lustre 55 Message: Any white glue will work. You can also try laminating your pictures. If a picture is varnished you should be able to apply epoxy directly over top. I also put the epoxy over shiney stickers without sealing them first with no problem. Good Luck |
| R. Chaine 10/13/2007 5:48:21 PM |
RE: Nu Lustre 55 Message: How can i apply nu-lustre inside a wooden salad bowl and such similar items |
| Neil 10/14/2007 7:14:25 PM |
RE: Nu Lustre 55 Message: A hard film finish is not recommended for wooden salad bowls. Try Terra Nova Naturoil on your unfinished wooden bowl. |
| R. Chaine 10/14/2007 8:54:41 PM |
RE: Nu Lustre 55 Message: Many thanks Neil for your quick answer. Actually my question was: How to apply nu-lustre over a round surface such as a concave surface or over a ball. The salad bowl was strictly as an example. I appreciatye your help. Thanks again. |
| Neil 10/15/2007 8:43:33 PM |
RE: Nu Lustre 55 Message: I have seen edges come out very nicely: 3 options: you have several options when it comes to edges. 1. allow the liquid to run over the edges. this will produce round edges. 2. pour on just enough liquid so that the product does not drip over the edge. this is the most difficult method as it requires an exact volume of liquid. 3. build a dam around the edges. coat the dam with a paste wax so that the dam can be easily removed from the cured epoxy. Concave is a little harder. You would have to do fine brush coats with a foam bruch to avoid runs. Swing apparently is comeing out with a brush on version of Nu-Lustre 55 . |
| Les 10/22/2007 9:44:53 PM |
RE: Nu Lustre 55 Message: Do I just pour this on or do I roll it or use a brush to even everything out. It is a big surface I am doing and I know I have to mix enough to do the whole surface but I want to make sure I get a nice even look. |
| Mark 10/23/2007 6:39:35 AM |
RE: Nu Lustre 55 Message: You would use a paint brush to apply a thin coat (warm bottles before mixing). Do some test pieces before attempting to finish the final project. |
| Les 10/23/2007 7:23:44 PM |
RE: Nu Lustre 55 Message: It would be up to a 1/4" thick in some spots because it is an uneven surface. |
| Mark 10/24/2007 9:40:35 AM |
RE: Nu Lustre 55 Message: That would require several coats. |
| Les 10/24/2007 5:01:41 PM |
RE: Nu Lustre 55 Message: So what you are saying is that I can't do it all in one coat. My understanding is that I could just mix up enough to do it all at once. Just mix and pour and make sure it is even and no bubbles, and if I end up with bubbles , just use a torch to warm them to get rid of them. |
| Mark 10/25/2007 6:04:40 AM |
RE: Nu Lustre 55 Message: You can only achieve 1/4 inch thickness in one pour if you dam the sides of the piece you are trying to coat. |
| Les 11/5/2007 5:56:53 PM |
RE: Nu Lustre 55 Message: I did my bar and counter tops last weekend and they turned out utterly fantastic. This Product is amazing. I would use this product any time. Everyone just has to read the instructions and make sure they put the bottle of resin into hot water until it becomes warm and will flow nicely. As well make sure they mix it really good with the hardener and don't worry about bubbles because they come out really easy with a propane torch just over top the mix after pouring, while it is still soft. There is lots of working time so there is no need to rush. I advise everone to do as I did and research and test it out before doing any big projects. Have fun and enjoy your results, I am! Thanks again for all your advice and help. |
| Sherie 2/4/2008 9:17:09 PM |
RE: Nu Lustre 55 Message: I have used this product on counters with great success but when I tried it on a counter with im imbedded pieces of glass I ran into problems. For some reason it wouldn’t set properly. I think I should have poured it in several layers but I poured it in one think layer. The left and right sides hardened faster then the middle, and it almost seems like the surface hardened faster then the under layers. Now the center part of the counter won’t harden at all. What should I do? |
| Neil 2/4/2008 10:31:23 PM |
RE: Nu Lustre 55 Message: The sticky spots are areas where the two components did not mix together. The epoxy will remain sticky forever - as it only hardens (cures) when A and B are thoroughly mixed together. You can usually cover sticky spots by applying another coat. The areas that have not cured should also come off with a good epoxy solvent like klenk's epoxy thinner. The klenks will remove the unreacted sticky spots. Follow the mixing instructions. You may have also tried to mix to big a quantity at one time. If you pour in stages degloss in between coats. Make sure not to under pour subsequent coats Good Luck |
| Sherie 2/4/2008 11:14:27 PM |
RE: Nu Lustre 55 Message: Thanks for the fast response. What should I use (tool wise) to remove the unreacted sticky area... there is a fairly large area. Also, when you day degloss between coats what does that mean? |
| Neil 2/5/2008 4:11:53 PM |
RE: Nu Lustre 55 Message: Gegloss with 320 sand paper. Try a scraper. What will you then do?? |
| Sherie 2/5/2008 5:00:14 PM |
RE: Nu Lustre 55 Message: So if I understand I should use a scraper and remove all the sticky -liquidy stuff. Then I will have a large dent in the center for the counter. Should then use klenk epoxy thinner and clean all the surfaces to remove all sticky parts that are left. Should the surface be solid then? Then I will fill the lowest area with more Nu Lustre 55. Once that is dry I will sand it with 320 sandpaper and pour another coat. Keep repeating this till I have a level surface. Does that sound good? |
| Neil 2/6/2008 7:05:53 PM |
RE: Nu Lustre 55 Message: I have done similar reapirs on a much smaller basis. You can give it a shot. |
| Steve 2/10/2008 4:20:30 PM |
RE: Nu Lustre 55 Message: How would you recommend applying the product to a 19 X 28" puzzle? Would it need to be sealed first? |
| Mark 2/10/2008 5:20:52 PM |
RE: Nu Lustre 55 Message: Glue the puzzle to a solid background - such as wood. If you DO NOT seal the surface, either with white glue or an acryic sealer, the joints will wet and turn a dark colour. Apply Nu-Lustre-55 as per instructions in the box (measure, mix and pour) |
| Bob 2/15/2008 2:21:49 PM |
RE: Nu Lustre 55 Message: I've got some Nu Lustre 55 and would like to use it on some older unfinished Terracotta tile I have kicking around. However, I'd just like to glaze the tiles. Can I use rubbing-alcohol, paint thinner, turpentine, or peroxide to reduce the consistency of Nu Lustre 55? |
| Mark 2/15/2008 2:28:11 PM |
RE: Nu Lustre 55 Message: Do not use any thinner - warm the bottles prior to mixing in order to achieve a thinner application. |
| Mark Cariou 2/28/2008 3:02:17 PM |
RE: Nu Lustre 55 Message: Is there a shelf life to this product? I have had it for about 4 years and used it two months ago without any problem, but when I used it again this week, it wouldn't dry on the wood, it is still tacky. |
| Mark 2/28/2008 4:59:02 PM |
RE: Nu Lustre 55 Message: I have used product that is over 10 years old with no problems. If the product does not dry, it is likely that a) the mixing ratio was not 1:1 b) the mixing was not done thoroughly and some unmixed liquid remained on the side/bottom of the container. If it does not cure after 48 hours, you will have to re-pour. |
| Mal 3/8/2008 6:12:38 PM |
RE: Nu Lustre 55 Message: Does anyone know if this product can be applied over rubber mat ? |
| Mark 3/9/2008 11:43:58 AM |
RE: Nu Lustre 55 Message: There should be not problem applying Nu-Lustre-55 over a rubber mat. |
| Mal 3/9/2008 1:06:25 PM |
RE: Nu Lustre 55 Message: Thanks for the reply Mark . Another question though . The frame for my bar is complete (about 10 ft. long)however , it is out of level by approx. 1/8" of an inch .I see a lot of questions regarding pooling of the Nu-Lustre . Is there anything i can do to minimize ? Do you know of a levelling compound i can use on the top of the bar frame before i install the top ? Thanks again for your help . |
| Mark 3/14/2008 9:30:57 AM |
RE: Nu Lustre 55 Message: What is the bar material? Can you remove the top from the frame? If you attempt to apply Nu-Lustre-55 onto a surface that is out of level by 1/8", you may notice a difference at either end. |
| Mal 3/14/2008 9:58:09 AM |
RE: Nu Lustre 55 Message: the bar top is 1" thk plywood . It''s screwed down and shimmed the best i could . I found a few self levelling concrete pour type compounds that should do the trick . Of course i''ll have to "box" in the top (and apply a release agent on the sides )to hold the compound in place till dry . This should work fine right ? Another question . are there any types of glue that should not be used with your product ? Thanks again |
| Mark 3/14/2008 12:57:47 PM |
RE: Nu Lustre 55 Message: Use a paste wax as the release agent - this works best. I have not heard of any glues that would interact with Nu-Lustre-55. However, you will want to ensure that the solvent has completely off gased before pouring. |
| Dave 8/2/2008 2:39:32 PM |
RE: Nu Lustre 55 Message: well to say the very least here all thesepostings are great anyway my question is this i`ve used a product in the past called nuclear i believe it was and i`m talking about 15/20 years ago i was in a camp in bc and i got into making crafts out of wood and this product i used was almost exact and i`m sure it has changed the name i could be wrong? but i have bought this new one nu-lustre-55 and to me it works amazing and how it brings the wood out is only from god and his wonders but my question is this is there any-way some-body would have any instructions on applying this i lost mine and can not find on the net which stuns me i`ve been reading here but only bits and pieces are said thanks for your time to go over this i can be reached at mdrl44@msn.com thanks once again SINCERELY DAVE IN HALIFAX |
| Mark 8/4/2008 10:14:43 AM |
RE: Nu Lustre 55 Message: Dave, You can download the directions directly from the Nu-Lustre-55 web page. www.swingpaints.com/1555.htm |
| DAVE 8/4/2008 11:04:03 AM |
RE: Nu Lustre 55 Message: thanks alot mark i did get this and appreciate this i thought i was right but just needed to confirm the way i was doing this but when doing some pieces i`ve noted that it is alot better when both bottles are warmed up seems to go alot further just my thinking and if i was doing a larger project i wouldnt thin so much.. once again all thanks for the response it was great in how you folks here replied so fast.. take-care bless DAVE IN HALIFAX NOVA SCOTIA |
| gary 8/27/2008 6:31:46 PM |
RE: Nu Lustre 55 Message: how good will it weather in direct sun light? used on a picnic table and other out door tables. |
| Steve 9/4/2008 3:03:24 PM |
RE: Nu Lustre 55 Message: applied Nu Lutsre 55 on my bar top turned out great but had a few uneven spots, so I poured another coat and now I have spots that are still tacky after a week. What when wrong did the same thing as before and is there a way to fix without reapplying or sanding. |
| Mark 9/4/2008 7:29:25 PM |
RE: Nu Lustre 55 Message: The sticky spots are the areas where the liquid was not completely mixed (usually from inadequate mixing on the sides and bottom of container). You will have to repour a new coat. |
| Steve 9/4/2008 10:41:33 PM |
RE: Nu Lustre 55 Message: This is my only choice nothing else will work? I have a large area will 1 bottle of resin and hardener work. the only reason i ask is that i've already put about 7 packages on the bar like I said it's large. Also can I just do the areas that are tacky or the whole thing. |
| Mark 9/5/2008 6:11:26 AM |
RE: Nu Lustre 55 Message: For best results, you should repour over the entire surface. Warming the bottles prior to mixing will give a thinner mixture that will flow out easier and go on thinner. |
| Yvonne Lacoursiere 9/29/2008 1:44:25 PM |
RE: Nu Lustre 55 Message: My husband made a coffee table with carvings in it. When he poured the Nu-Luster-55, some areas turned quite cloudy. Any way to remove that cloudiness and what caused it in the first place? Yvonne |
| Mark 9/29/2008 2:02:50 PM |
RE: Nu Lustre 55 Message: Assuming there was nothing on the surface of the table prior to pouring the Nu-Lustre-55, is it possible that the cloudiness that you see is the presence of many very small bubbles? |
| Brock 9/30/2008 8:37:27 AM |
RE: Nu Lustre 55 Message: Hi,I built a bar outside on my deck.It is mostly under an overhang but will definately get rain,snow and direct sunlight.It is conered with 12" porcelen tile,I have edged the top corners with aluminum angles which are 3/16" thick.Before I read your specs I sealed the grout with sealer that I suspect is silicone based.Can I mitigate the effect of the silicone with anything and will this product endure the outdoors as well as the porcelin tile that I used,Thanks for your help,Brock. |
| Michel Bordeleau 10/13/2008 9:47:20 AM |
RE: Nu Lustre 55 Message: I've tried Nu-lustre 55 recently and I must say that I'm very satisfied of the product. Tried an other brand before and had much more problems with the bubbles and the smell was stonger. I'v tried to make some coaster with picture on a ceramic tile the finished product is beautiful but the surface not hard enough. If I put a hot coffee mug on it, it will makes some marks that I can't removed without putting an other coat, not very practical. Do you have a solution for that? |
| Mark 10/14/2008 6:03:19 AM |
RE: Nu Lustre 55 Message: How long did you allow the finish to cure prior to placing a hot mug onto it? Nu-Lustre-55 should reach its maximum durability after a period of about 30 days. |
| Michel Bordeleau 10/14/2008 11:16:01 AM |
RE: Nu Lustre 55 Message: Thanks for your answer Mark. Effectively I only allowed a few days. So I,ll try after 30 days. |
| Jules Lauzon 10/18/2008 11:22:37 AM |
RE: Nu Lustre 55 Message: I've used this product on serveral tables, some came out fine others not so much. Just wondering if there's a way to sand and polish the surface smooth? Repouring didn't work, and is getting expensive. I followed the instructions to the "T". Thank you |
| Mark 10/19/2008 7:34:51 AM |
RE: Nu Lustre 55 Message: You can sand and polish any finish. What do you mean repouring didn't work? Did you not apply enough Nu-Lustre-55 to completely recover the surface? |
| Michel Bordeleau 10/24/2008 3:47:46 PM |
RE: Nu Lustre 55 Message: I've made some photo tiles with Nu lustre. Result is great but some tiles came out with some dust. I know that I can sand the tile and recoat but I would like to know if I can dilute Nu Luste to recoat or otherwise use and other product. What would be that product or how can I dilute Nu lustre? |
| Mark 10/24/2008 3:57:15 PM |
RE: Nu Lustre 55 Message: It is best not to dilute the product, although I have had some success using Klenk's Epoxy Thinner and denatured alcohol. In order to apply a thin coat, you can warm the bottles prior to mixing. |
| Derek 1/15/2009 10:24:27 AM |
RE: Nu Lustre 55 Message: I have a Bar top which came out fantastic. I had a friend who dropped a beer mug on top and cracked the surface. How can I repair a dime size crack? Thanks |
| Mark 1/15/2009 10:35:18 AM |
RE: Nu Lustre 55 Message: You can cut or route out the affected area. Remove all dust. Warm the two bottles of Nu-Lustre in a bath of warm water (approx 40C). Mix the two components and immediately pour into the hole so that the section is slightly over-filled. NOTE: warm mixture will set of quicker than room temperature mixture. After approximately 6 hours, use a sharp blade to level the surface. |
| Derek 1/15/2009 10:49:09 AM |
RE: Nu Lustre 55 Message: Thanks Mark.....will do. |
| Tanya 1/24/2009 12:35:18 PM |
RE: Nu Lustre 55 Message: Hi Mark, I have a number of mosaic tables that I epoxied with nu-lustre 55. I sealed the grout and let them dry for 72 hours before epoxying to ensure they were dry and cured. Initially the tables looked great but after about 6 weeks they went cloudy and now look terrible. 1. why did this happen? 2. how can I fix it? can I remove the epoxy? This was a large job of 6 tables for a client and they are furious. Please help! Tanya |
| Rob 1/24/2009 5:03:41 PM |
RE: Nu Lustre 55 Message: I have used Nu Lustre 55 many times to resurface tables and counter tops. The last application of Nu Lustre 55 was over a new counter top of marble tiles. Some dust and hair landed on the surface as it was drying. I've used five one gallon kits for this job. Repouring will be expensive, but necessary. I would like to repour a thin coat over the entire surface to cover the barely noticable debris trapped in the smooth level surface, without having to purchase another 5 kits. I know you recommend not diluting Nu Lustre 55, and that Klenk's Epoxy Thinner may be used to thin this product down. Please tell me the recommended amount of epoxy thinner required to thin out a one gallon kit. Thank you, Rob |
| NEIL 1/26/2009 12:14:44 AM |
RE: Nu Lustre 55 Message: TRY thinning the product by heating the bottles in warm water |
| Rob 1/26/2009 1:13:05 PM |
RE: Nu Lustre 55 Message: Thanks for your reply Neil, however you did not answer my question. I do heat the bottles in hot water for a minimum of ten minutes just prior to mixing, as per the instructions enclosed with the product Nu Lustre 55. I know that Nu Lustre 55 can be thinned out using epoxy thinner. My question is - How much epoxy thinner is required or needed to thin out a one gallon kit while mixing together just prior to pouring? Thank you, Rob |
| Neil 1/26/2009 6:55:19 PM |
RE: Nu Lustre 55 Message: I have never reduced the nu lustre with the epoxy thinner. I do not know if it works. You can fool around with it. |
| Dan 2/24/2009 8:58:03 PM |
RE: Nu Lustre 55 Message: I am making a bathroom vanity top with a bullnosed edge. How can I get the nice thick edges I see on many resturant tables using Nu- Luster 55? |
| Neil 2/24/2009 9:02:39 PM |
RE: Nu Lustre 55 Message: I am not sure what bull nose is. can you send a pic? |
| Dan 2/24/2009 9:44:03 PM |
RE: Nu Lustre 55 Message: A bull nose is a roundover on both the top and bottom of the countertop. |
| Neil 2/24/2009 10:38:05 PM |
RE: Nu Lustre 55 Message: This requires a little technique. As the epoxy dries you can brush the dripping epoxy upwards over the rounded edges. You keep on doing this… it takes a little work. If it is not thick enough you can brush on a second and third coat on the rounded edge. Apply wax so the epoxy does stick to the underside. Then chip off the beads that form the next day. You may want to practice this on some scrap before going directly to your job. |
| Dan 2/24/2009 11:39:23 PM |
RE: Nu Lustre 55 Message: Thanks for that quick reply. I have to wait a few weeks till our weather gets warmer. |
| Marc Augier 2/26/2009 8:29:50 PM |
RE: Nu Lustre 55 Message: Hi, I used Nu-Lustre on my bar counter and need to put a second coat because it is not thick enough. Do I need to sand it before? I heard it won't stick to it if not? Thanx |
| Mark 2/27/2009 8:00:30 AM |
RE: Nu Lustre 55 Message: It all depends on how long ago the first coat was applied. |
| marcaugier 2/27/2009 10:15:24 AM |
RE: Nu Lustre 55 Message: Last week |
| Mark 2/27/2009 10:17:07 AM |
RE: Nu Lustre 55 Message: You are probably at 95% hardness. I would give the surface a light sanding to remove the gloss prior to applying a new coat. |
| Jane 3/12/2009 9:58:43 AM |
RE: Nu Lustre 55 Message: I use NU LUSTRE 55 to create water in miniature. I poured an ocean 1/8" at a time. It sets and looks wonderful. The solid set part is about 1 1/2" thick so far. The last layer didn't set totally. There are a few very thin sticky spots. I'm think it's as you say, the bottom of the conatiner not mixed properly. I can't really sand, as there are props protruding and the area is partially enclosed. Can I repour right over top with no prep to the sticky spots? The surface does not need to be smooth or even. |
| Mark 3/12/2009 10:01:42 AM |
RE: Nu Lustre 55 Message: You can use Super DeGooper or Klenk's Epoxy Thinner to remove any of the sticky spots. You can then pour over the surface. |
| Jane 3/12/2009 10:08:27 AM |
RE: Nu Lustre 55 Message: Do you know if those products are available in NS? |
| Mark 3/12/2009 10:11:22 AM |
RE: Nu Lustre 55 Message: Super DeGooper is available at Home Hardware, Wal-Mart, etc. Klenk's Epoxy Thinner is available at Home Hardware, Kent, etc. |
| Jane 3/12/2009 12:24:24 PM |
RE: Nu Lustre 55 Message: Found DeGooper. How would you suggest I apply it to prepare the sticky surface for a another coat? |
| Mark 3/12/2009 12:28:51 PM |
RE: Nu Lustre 55 Message: As the directions state: Apply Super DeGooper to a cloth, blot, and rub lightly until spot is removed. |
| Jane 3/13/2009 8:37:41 AM |
RE: Nu Lustre 55 Message: I've made a mess. The goo goes a little deeper then I though fisrt off. Can I send a couple of pictures somewhere so you can get a better idea what I'm looking at? |
| Mark 3/13/2009 8:39:07 AM |
RE: Nu Lustre 55 Message: info@swingpaints.com |
| Jane 3/13/2009 9:01:22 AM |
RE: Nu Lustre 55 Message: Mark, I had to remove the fishing shack totally to get at the water that was poured under the wharf. The water ( product) underneath is solid, but the top 1/8" - 1/4" (in spots) is as you see, semi set. The smoothness of the finished piece doesn't factor into this at all. In fact, this may have been a mistake, that has allowed me to depict some water movement. The DeGooper process seems like it could take several bottles and never really lift it entirely. What happens to the sticky spots if I just pour another layer on top? You have been extremely helpful. Wonderful representation for your company! With this help, I would not be intimidated or hesitate using any of your products. |
| Mark 3/13/2009 11:46:13 AM |
RE: Nu Lustre 55 Message: Jane, I have taken the liberty of putting your e-mail online so that everyone can benefit. Firstly, the "sticky" spots are caused by incomplete mixing of the two components. This generally occurs when the mixer does not get the corners of the mixing container. When I mix, I always use containers that are less than half full when measured. I then pour all of component A into container B and mix thoroughly. I then pour the entire mixture back into container A and mix thoroughly. I will do this several times to ensure everything is mixed. A bit more time and effort, but I have never had "sticky" spots. There are a couple options at this point based on the thickness of the "sticky" spots. If you want to remove all the "sticky" spots, you can dig out the majority of the "sticky" spots with a popsicle stick and then use the Super DeGooper to remove any residue. In this manner, the entire finish will be properly cured. Since you are not using this as a table or bartop, and these spots are fairly thick, my suggestion is simply to pour over the "sticky" spots. Warm the individual bottles in hot water in order to lower the viscosity. Mix the components and pour onto the surface. The new mixture will harden and cure over your "sticky" spots. Remember, the warmed mixture will cure FASTER than would a room temperature mixture, so you have a lot less working time. Let me know how things turn out. Mark |
| Stan 3/16/2009 1:10:25 AM |
RE: Nu Lustre 55 Message: our hardwood floor has a number of deep scratches (polyurethane finish),can I use NU LUSTRE over the finish? |
| Mark 3/16/2009 8:02:27 AM |
RE: Nu Lustre 55 Message: Yes, you can apply Nu-Lustre-55 over a polyurethane finish. You can use it to fill the deep scratches. |
| Stan 3/16/2009 3:16:47 PM |
RE: Nu Lustre 55 Message: Thanks Mark |
| Audrey Brown 3/29/2009 4:11:13 PM |
RE: Nu Lustre 55 Message: I am thinking about using Nu Lustre 55 on stones since tumbling takes a long time. What would be the best/easiest way to apply the product and is the product non-yellowing. Thanks so much for your assistance! |
| Mark 3/30/2009 6:02:44 AM |
RE: Nu Lustre 55 Message: The best product for your application would be Nu-Lustre Brush-On Anti-UV. This product is designed for application to non-horizontal surfaces, and will not turn yellow. |
| Audrey 3/30/2009 4:27:03 PM |
RE: Nu Lustre 55 Message: Thanks so much, Mark!! |
| Mélanie 4/5/2009 7:23:23 PM |
RE: Nu Lustre 55 Message: Bonjour, Lustrage Nu-lustre55: Les pièces moulées en époxy-résine peuvent être lustrées au moyen d'un disque ou d'une roue à lustrer en utilisant des abrasifs pour plastiques pour donner un fini ultra brillant. Est-ce-vrai? Si oui, j'aimerais savoir quels accessoires utiliser pour le lustrage et les techniques pour obtenir un effet miroir. Cela me permettrait de réparer les imperfections obtenu avec l'usure sur le dessus de ma table de cuisine. Sincèrement- Mélanie;) |
| Jay 4/5/2009 7:48:32 PM |
RE: Nu Lustre 55 Message: I just coated my entire bar this weekend with nu-lustre 55 and I must recommend definetly using a propane torch if you are using this product. I was worried when we spread the product as it was quite cloudy. I thought it was maybe becuase of the thickness but after using the torch it ended up like glass. I am wondering if i should put a cover over the nu-lustre to scratch proof the bar? I see Antiquax has been used but it is not as resistent to water as the nu-lustre. Any opinions using a cover over the nu-lustre to avoid scratches? |
| Mark 4/6/2009 9:34:37 AM |
RE: Nu Lustre 55 Message: Mélanie, N'import quelle méthode de ponçage peut être employée pour modifier le lustre de Nu-Lustre-55. Vous pouvez acheter le matériel aux magasins qui vendent les produits professionnels de finissage. |
| Mark 4/6/2009 9:37:05 AM |
RE: Nu Lustre 55 Message: Jay, Nu-Lustre-55 is definately not scratch proof, but applying a coat of Antiquax Marble Wax will certainly limit most scratches. Wax is very water resistant, and if the wax does fail, it is very easy to apply another coat. What type of cover would you put over the bar? |
| Carmel 4/11/2009 5:27:35 PM |
RE: Nu Lustre 55 Message: bonjour j'aimerais savoir ce que vous entendez pas colorant universel merci Carmel |
| Robb 4/16/2009 4:21:42 PM |
RE: Nu Lustre 55 Message: Hi Mark, I'm getting to the finishing stages of a dining table made from 150yr old salvaged hemlock. The wood was underground for many years and is full of character. A little too much character for my clients though. There is some cracking and a little insect damage. A fellow furniture builder recommended a Circa 1850 pour in/on epoxy to fill these voids. I was told that I could tint the epoxy with 1 or 2 drops of acrylic craft paint to mimic a bark opening or come close to the finished colour. My question is twofold. First, is the product suitable for this application and second, will a sprayed poly like the Bowling Alley finish adhere to the epoxy? Thanks, Robb in Guelph, Ontario |
| Mark 4/17/2009 9:07:30 AM |
RE: Nu Lustre 55 Message: Using Nu-Lustre-55 to fill gaps and voids is perfectly acceptable. You can add acrylic paint to the epoxy, although this tends to lessen the overall strength and gloss levels. It would be best to use either universal colourants or artist pigments. Only a very small amount of colourant is required and recommended. If you do use acrylic paint, the cure time will dramatically increase. If you are anticipating using the Circa 1850 Bowling Alley Polyurethane, you should wait a minimum of 1 week if tinting with paint. If you use universal colourants or artist pigments, 48 hours is recommended prior to applying the Bowling Alley finish. |
| Robb 4/17/2009 8:49:07 PM |
RE: Nu Lustre 55 Message: Thanks Mark. I picked up the nu-lustre today and will be test-driving it tomorrow. Can you tell me where to buy the Bowling Alley finish in my area? I've been able to find other Circa 1850 products at the larger hardware stores in Guelph but not this one. Thanks, Robb |
| Neil 4/17/2009 9:32:08 PM |
RE: Nu Lustre 55 Message: ROYAL CITY PAINTS 226 SPEEDVALE OWNER TONY & LYNN COLONARDI. THESE GUYS MAY BE ABLE TO BRING THE BOWLING ALLEY IN FOR YOU RONA 55 DAWSON RD. PAINTS JILL BENALLICK. THEY CAN BRING IT IN SPECIAL ORDER HER ARE THE RONA PART NUMBERS Code RONA CIRCA # Description UPC CODE 0776001 181825 VARNISH POLY.GLOS.250ML 181825 0776002 181801 VARNISH POLY.GLOS.1 LT 181801 0776003 181804 VARNISH POLY.GLOS.4 LT 181804 0776004 181925 VARNISH POLY.SAT. 250ML 181825 0776005 181901 VARNISH POLY.SAT. 1 LT 181901 0776006 181904 VARNISH POLY.SAT. 4 LT 181904 WHERE DID YOU BUY THE NU LUSTRE? |
| Robb 4/17/2009 11:00:04 PM |
RE: Nu Lustre 55 Message: Thanks Neil, I purchased the Nu-Lustre at the Rona store. I prefer to support the local small business community so I'll check with Royal City about the poly. Robb |
| Neil 4/18/2009 2:51:52 PM |
RE: Nu Lustre 55 Message: If the Store owner contacts me I can run some up to him to sell to you. Good Luck |
| Bob FIsher 4/20/2009 4:43:07 PM |
RE: Nu Lustre 55 Message: Question on finishing surface with Oil based stain before putting playing cards to be covered with Nu-Lustre-55 In order to have the correct colour, want to put an oil based stain on fir wood, then glue playing cards to surface. will use the white glue/water coating as suggested in product handout followed by Nu Lustre 55. Should be no problem? Thanks in advance Bob 780 718 2257 |
| Mark 4/21/2009 6:49:33 AM |
RE: Nu Lustre 55 Message: Sounds like a great idea. |
| Laurel 5/5/2009 2:22:44 PM |
RE: Nu Lustre 55 Message: Hello, I used an epoxy product for my countertops and bartop (Glaze Coat by Famowood), and it hasn't turned out well at all. We can't get any help from Famowood customer service, and we're trying to figure out what to do next. It has been almost 3 weeks, and paper products stick to the surface, leaving paper stuck in the epoxy. Anything that weighs more than a few ounces seems to leave indentions. For example, my husband put his elbows on the bar for 5 minutes or so, and when he moved, there was a huge dent in the surface. I'm guessing that the instructions/guidelines for both products are similar. I think our humidity was higher than 50%. Could that have caused the problems we are having? If we get the humidity down for a few days, could it harden, or have we missed our window? Also - the instructions in the Famowood Glaze Coat says that the product is pliable - and if something heavy is left on the surface for an extended period of time, it will leave an indention that will eventally even back out. Is the same true of your product, or does it completely harden? Thank you, Laurel |
| Mark 5/5/2009 2:26:55 PM |
RE: Nu Lustre 55 Message: Can't get help from customer service? So what's the point of having a customer service? Epoxy products all work on the same principle. Two component are mixed; they react; they harden. The most common cause of a sticky surface is incomplete mixing. If leaving a something heavy on the surface causes it to dent, this is certainly not a product that I would use for a coutertop or bartop. In general, it takes several weeks for an epoxy to completely cure, but once it has cured it will not dent due to a heavy object. With all that said, the coating that you have applied will never cure. The high humidity would have affected the cure time and possibly the gloss level, but would not lead to a sticky surface - that is from the mixing. At this point you should use a solvent (either epoxy thinner, Super DeGooper, or isopropanol) to remove as much of the sticky areas as possible. Flood the surface with a solvent and use a rag to wipe it up. After everything has dried, you can repour the surface. |
| Laurel 5/5/2009 3:21:26 PM |
RE: Nu Lustre 55 Message: Thank you Mark. I'll definitely use your product to repour the surface. When you say to flood the surface with a solvent - do I need to let the solvent set for a while before wiping it off? Do I also need to sand the entire surface before repouring, or can I just pour on top of the old stuff? |
| Mark 5/5/2009 3:29:14 PM |
RE: Nu Lustre 55 Message: These solvent evaporate very quickly, so you need to pour on a sufficient amount so that the surface remains saturated for several minutes. This may require multiple applications. Do not worry about removing every sticky spot. The new finish will set regardless. Sanding the surface will certainly increase adhesion between coats. You will not be able to sand the sticky spots, so try to remove as much as possible as per directions above. You should sand with 400 or finer sandpaper so that the gloss is removed. |
| Laurel 5/5/2009 4:00:05 PM |
RE: Nu Lustre 55 Message: Thank you very much for your help. I really appreciate it. |
| Roy Smith 7/26/2009 8:53:53 PM |
RE: Nu Lustre 55 Message: I have poured the product over a table top (195 yr old oak tree). It looks fantastic, with the exception of a few spots where air came through. I used a straw to blow out many air bubbles, but these ones where right as it was almost dry - they are now little "divots". Can I pour over these spots, or do I have to re-pour the whole thing? Do I have to do anything to the surface before re-pouring? Thanks |
| Simon 7/27/2009 1:33:43 PM |
RE: Nu Lustre 55 Message: Can I pour Nu Lustre over a table top that is already covered with lacquer? |
| Mark 7/28/2009 12:02:32 PM |
RE: Nu Lustre 55 Message: Yes, you can pour Nu-Lustre-55 onto a surface that has been finished with a lacquer. |
| Mark 7/29/2009 9:47:40 AM |
RE: Nu Lustre 55 Message: Roy, The air bubbles that you experienced is a common occurance when dealing with older wood. For those surfaces, it is ALWAYS best to apply a seal coat. However, what's done is done. You cannot just fill the spots, you will have to repour the entire surface. The first thing to do is to ensure the surface is completely clean. Be sure to remove any dirt, wax, grease, etc. Lightly sand the surface with the finest grit sandpaper you have. The finer the grit, the less likely you are to leave any scratches. However, even with 200 grit sandpaper I have never notices any scratches after repouring. Since you are only looking for a thin coat, you should warm the separate bottles of Nu-Lustre-55 in a pot of water. Do a quick test by mixing a very small amount of each compoent together in a separate container. Notice the thin viscosity. Pour only a piece of scrap and observe how long it takes to begin to gel. It is better to make your mistakes on the test piece than to ruin your beautiful table. After testing, mix the components and repour. Ensure you have enough epoxy to entirely cover the surface. Be sure to send up a picture of your project. An online photo gallery is upcoming. |
| Chris 7/31/2009 3:32:13 PM |
Nu Lustre 55 Message: I've made a table and want to pour Nu-Lustre-55 over it. I want it to run over the rounded edges and down the side of the table about 1 1/2". The table is almost 4' X 6'. How can I make sure it will run over the edges evenly and what can I put on the bottom of the edge to keep it from all runing off? I'm in Ancaster, where can I buy it locally? I checked HD and they don't have it. Thanks |
| Mark 7/31/2009 3:48:50 PM |
RE: Nu Lustre 55 Message: As long as you pour on more liquid than will cover the top, the excess will run over the edges. You will want to wax the underneath to keep it from sticking there. The thickness of Nu-Lustre-55 on the sides will not be as thick as the top. You can achieve an even finish by brushing the edges over a period of an hour or two to prevent uneven drips. Home Depot does not carry that product. You can find it at most Rona stores. |
| mike 8/14/2009 1:16:23 PM |
RE: Nu Lustre 55 Message: Is it safe for aquariums want to use it on my cement background. |
| Mark 8/14/2009 1:31:25 PM |
RE: Nu Lustre 55 Message: Yes, Nu-Lustre-55 is safe to use in aquariums once it has completely cured. Epoxies will take up to 30 days to completely cure. |
| mike 8/14/2009 2:20:05 PM |
RE: Nu Lustre 55 Message: Thanks thats good news |
| billy b 7/7/2010 12:57:02 PM |
RE: Nu Lustre 55 Message: hello i been looking for a product to cover some old doors sound like is my stuff iam in baton rouge la where can i find it and does it come in gallon or more got a lot of doors billy |
| Mark 7/7/2010 3:42:45 PM |
RE: Nu Lustre 55 Message: No one down there carries this product. You can order online at jamestowndistributors.com |
| caroline 7/26/2010 10:41:55 AM |
RE: Nu Lustre 55 Message: is it possible to apply the product on top of an acrylic based paint or oil based paint? |
| Mark 7/26/2010 11:31:47 AM |
RE: Nu Lustre 55 Message: You can apply Nu-Lustre-55 over any cured paint. |
| Alistair 10/11/2010 2:21:08 PM |
RE: Nu Lustre 55 Message: Hi , Have been using Nu-Lustre-55 for a few years now . Amazing product - the perfect finishing touch to many projects. Can you advise if there are larger kits available than the 3.78ml and if so where do I find them / or order them from . Live close to Kitchener and London Ontario area . Thanks , Alistair |
| Mark 10/11/2010 3:19:29 PM |
RE: Nu Lustre 55 Message: The largest size that we package is the 3.78L kit. However, we do sometimes have returns from stores in which the resin and/or hardener has begun to amber. I will have them added to our web site for ordering. |
| joe 11/14/2010 4:39:11 PM |
RE: Nu Lustre 55 Message: I poured a 39 sq ft bar top over rough cut cedar. I had a few sticky spots, so I tried to repour over them. I ended up with a lumpy mess (and more sticky spots!) So, I sanded the top down with 180 grit, by hand, then mixed with a mixing attachment on my drill AT VERY LOW SPEED, so as not to make air bubbles. I poured it again and it came out awesome. The directions say not to use a power mixer, but if you do it slowly, it will certainly mix the 2 parts well enough to avoid sticky spots. |
| joe 11/14/2010 4:43:05 PM |
RE: Nu Lustre 55 Message: Also, I did not remove the sticky spots.. I simply scuffed up the good areas (and sanded down the lumpy areas from the "touch up")I wiped down the the entire top & sticky spots with acetone. The new pour reacted and hardened the sticky areas and covered everything else flawlessly. |
| Mark 11/15/2010 12:53:39 PM |
RE: Nu Lustre 55 Message: Joe, Thank you for taking the time to post your procedure and comments. I am glad that your project eventually worked out to your satisfaction. As you noted, we do not recommend using a power mixer. The reason is that a power mixer can pose a problem if you run it at high speed. The problem is not bubbles in the mixture(all bubble will disappear by exhaling onto the surface, or by using a torch), but the fact that high speed mixing can lead to a quick increase in temperature. When the temperature increase too quickly it can cause the chemical reaction to proceed at an accelerated rate and lead to a mixture that hardens in the mixing container. |
| Edith 12/6/2010 1:03:24 PM |
RE: Nu Lustre 55 Message: Hello! Is it possible to touch up scratches on the finish by sanding+polishing ? I guess it is but I wonder what polishing ways you would suggest so it becomes super shiny again after sanding the imperfection. Thank you! |
| Mark 12/6/2010 1:09:56 PM |
RE: Nu Lustre 55 Message: It is possible. You need to start with the finest sandpaper that will remove the deepest of the scratches - could be as fine as 800 or as coarse as 200. After sanding out the scratches, you will need to progress to finer and finer sandpapers, until you end with super fine wet/dry sandpaper. After the sandpaper, you will need to continue buffing with pumice stone (from coarsest to finest) and finally with rottenstone. |
| Edith 12/6/2010 1:26:20 PM |
RE: Nu Lustre 55 Message: Thank you Mark. One last question: is it possible to buy the required material (sandpapers, pumice and rottenstone) at Swing paint? If so, is there a pre- made sanding/polishing kit we could add to our next Purchase Order? |
| Mark 12/6/2010 1:37:37 PM |
RE: Nu Lustre 55 Message: Unfortunately, we do not supply these items. |
| Steve 12/23/2010 11:02:48 PM |
RE: Nu Lustre 55 Message: Does this product self level I have a 4x8 table top with live edge what do I use to level out product as I poor |
| Mark 12/24/2010 7:35:02 AM |
RE: Nu Lustre 55 Message: Simply spread out the product - allowing enough product to fully cover the surface. It will self level. |
| David 2/10/2011 8:09:15 AM |
RE: Nu Lustre 55 Message: I have been using this product for many years with my art and about to embark on selling my product wholesale. I know how to use-I just don''t the chemical make-up. Clients want to know: 1. any animal by-product involved 2. any hazardous chemicals involved...now I know its toxic in its raw form, but after its cured properly, I''m assuming its safe? If someone could reply with the chemical make-up or any environmental concerns it may have...I say that after its cured--its safe, just want to be informed so I know what I''m talking about when I have customer queries. |
| Mark 2/10/2011 9:18:07 AM |
RE: Nu Lustre 55 Message: David, Organic material are mostly derived from plants. Animals eat plants, and in turn fertilize plants. Animals and plants may be converted back into carbon dioxide, or, after eons, into coal, natural gas, petroleum, etc. When these burn or are processed, they may again be taken up by plants, or directly ingested by animals. So in reality, we all just share the near infinite atoms that make up the earth (ignoring meteorites for now). The most common animal derivative in paints is from rendered tallow. The tallow is usually made into a glue-like material that bonds the pigments. Another animal by-product, shellac, comes from the secretion of the lac bug. Ok - enough of the lecture. The answer to 1. is that it would be quite a task to trace the history of each individual component to determine if animal products are used in the process. Most likely, the organic materials are derived from petroleum and vegetable oils. The answer to 2. is quantifiable, but is based on current information. In its raw form, Nu-Lustre is not considered toxic as defined by the Health Canada. If it were, there would be a skull & crossbone symbol and specific warnings on the package. Once cured, Nu-Lustre is not known to be toxic. |
| David 2/10/2011 9:51:57 AM |
RE: Nu Lustre 55 Message: Thanks for the prompt reply! I completely understand the 'lecture', and agree-- the forms I have to fill out that some shops send me are over the top. I really appreciate the information! |
| Sylvia 11/11/2011 10:44:34 PM |
RE: Nu Lustre 55 Message: I want to do a hardwood floor that has grooves about 1/4" deep between each slat. How would I go about getting a thin coat on the floor but thick enough to level out the grooves?...Thanks. |
| Mark 11/14/2011 9:01:50 AM |
RE: Nu Lustre 55 Message: Nu-Lustre-55 will self level, so you would simply spread the epoxy onto the floor. Depending on the depth and width of the grooves, you may want to apply the Nu-Lustre-55 in multiple coats. The first coat would fill in most of the grooves, and the second coat would give you a uniform surface. |
| jason 4/15/2012 11:19:21 AM |
RE: Nu Lustre 55 Message: hey mark, have had. great success with the nu lustre 55. have poured over a couple of live edge tables that i have made and been very pleased with the results. finding it very difficult to avoid airbourne contamination in my work space. tables have had proper time to cure, but have lint/dust particals across the surface. can you reccomend a suitable rubbing compound that may allow me to buff and polish these things off? |
| Mark 4/15/2012 5:27:05 PM |
RE: Nu Lustre 55 Message: Glad to hear of your success. Buffing and polishing can be done, as with any other hard finish. Start with the finest frit that will remove the imperfections (200/400/600). Keep sanding with finer and finer grits, eventually ending with ultra fine wet/dry sandpaper. After all the sanding, the surface will be smooth, but not shiny. In order to get back the high gloss, you will have to buff with pumice stone 1F, 2F, etc., followed by rotten stone. As you can see, it is a big job. There are two things that can help to alleviate the problem of dust. The first is to work in as clean an environment as possible. Wet down the walls and floor to remove all the dust. The second is to build a tent that sits a few inches above the table top. The tent can be made of anything (e.g., cardboard, wood, etc.). Since the dust primarily settles down from the air, the tent should keep the dust off the top,of the surface. |
| Nicole 5/30/2012 12:02:23 PM |
RE: Nu Lustre 55 Message: I have a bar top that we just finished with nu lustre 55. The surface was completely level when the epoxy was poured (I checked it about a 12 times) but we have very visible wave as well as areas that looks as though they have not been fully covered. It is for a commercial space and the finish needs to be perfect! How do I go about fixing it? If there is a couple dust spots how do I get rid of those as well. Thanks! |
| Mark 5/30/2012 12:22:01 PM |
RE: Nu Lustre 55 Message: Nu-Lustre-55 is a self-leveling coating, so it will be completely level when it is poured. However, there are several things that will cause it to become non-uniform. If a propane torch, heat gun, hair dryer or other heat source is used in an attempt to eliminate the air bubbles, and the tool is too close to the surface, it will cause waves. If an insufficient amount of Nu-Lustre is poured onto the surface, the epoxy will eventually pull back leaving areas that are no longer covered. The best way to solve the problems that you described is to sand off the dust spots and repour a new coat. In order to eliminate dust spots, the area must be very clean and free of dust. You can build a cardboard/wood/plastic tent to sit a few inches above the surface during curing so as eliminate dust. |
| Nicole 5/30/2012 12:57:38 PM |
RE: Nu Lustre 55 Message: Thanks you for your reply. Just a couple more questions: How far do I sand down? What grade sand paper should I use? If bubbles or waves appear on the top coat, what is that best way to get rid of them? What effects does humidity have? And will I still get clear finnish? Thanks Again! |
| Mark 5/30/2012 1:09:06 PM |
RE: Nu Lustre 55 Message: You probably only want to sand off the dust specks, and that can be done with as fine a sandpaper as will do the trick. You do not need to sand to a level surface as the new pour coat will go on level. For a small surface, bubbles can be eliminateed by blowing onto the surface through a straw. For larger surfaces, a butane torch is best. Hold it several inches from the surface and move the torch quickly over the surface. The bubbles should be disappear immediately. You should be getting waves, but if you do, you will have no choice but to hope they disappear by themselves, or repour. Humidity will slow the cure time. If the humidity is really high, it may cause the surface to become cloudy or less glossy. |
| Nicole 5/30/2012 4:33:48 PM |
RE: Nu Lustre 55 Message: Sorry just need to know if it will still have a clear finish? Thanks |
| Mark 5/30/2012 4:41:28 PM |
RE: Nu Lustre 55 Message: Why not? |
| Garret 5/31/2012 4:06:22 AM |
RE: Nu Lustre 55 Message: I have been using this product for my burl tables and clocks and have never had a problem. |
| charly 6/4/2012 12:21:16 AM |
RE: Nu Lustre 55 Message: i have poured the nu luster on a painted colaged surface,can i now add more collage and apply another layer of nu luster over it. And if so how long should i wait before putting another coat of nu luster on the first one. |
| Mark 6/4/2012 6:51:35 AM |
RE: Nu Lustre 55 Message: That shounds like it is going to be a very cool looking piece. You can certainly pour multiple coats of Nu-Lustre. You should wait at least 24 hours between coats - more if you are pouring in temperature below 25C. |
| Nicole 6/6/2012 11:49:43 AM |
RE: Nu Lustre 55 Message: Hi Again. So my contractor royally messed up my counter top. He did not mix properly and now there are large sticky spots. He did not use enough epoxy and there are high and low spots. He also came in and sanded other materials in the room afterwards and now there is dust everywhere (including the sticky spots). There are areas where the epoxy has hardened (with dust embedded) but it is gooey underneath. If I understand correctly I should: 1. Scrape out sticky spots 2. Use an epoxy thinner to clean out the spots (I''m worried that it will also take off the paint on the bar underneath) 3. Sand off the dust from the hardened areas 4.Clean the entire room and surface 5. Make a trench 6. Re-pour A couple questions: 1.What I do for the hardened spots with goo underneath? 2. Do I sand the hardened spots first then use the epoxy thinner? 2.How do I build a trench? (The bar is line with Brass) 3.When I re-pour, do I first fill in the holes created by the removal of the sticky spots, sand then re-pour? Or do I just re- pour the entire bar? 4. How much epoxy do I need? The bar roughly 70 square feet. Thanks so much for your help. It looks like a disaster and we were supposed to open our restaurant yesterday! |
| Mark 6/6/2012 1:48:55 PM |
RE: Nu Lustre 55 Message: YIKES! Where are you located? Can you send pictures? |
| Nicole 6/6/2012 2:42:26 PM |
RE: Nu Lustre 55 Message: We are located in Montreal. I"ll send some pictures through email. Thanks |
| Pasca 6/20/2012 10:48:56 PM |
RE: Nu Lustre 55 Message: Bonjour, J''ai appliquer mon Nu-Lustre-55 sur mon comptoir de cuisine. Malheur, j''ai plein de micro-bulles qui se sont créee. J''ai essayer de les enlever à la torche, mais ca n''a pas fonctionner. Ce matin, le vernis est sec et plein de petits picos qui donne une texture tres rugueuse.. Comment faire pour m''en débarasser? Comment faire pour que ca ne se reproduise pas sur mon second comptoir? merci |
| Mark 6/21/2012 10:39:01 AM |
RE: Nu Lustre 55 Message: Avez-vous faites des testes des petits tests avant de l''appliquer à votre compteur? Il est vraiment important de se familiariser avec le produit avant de verser sur une grande surface. Quel type de surface est votre comptoir? Avez-vous utiliser une couche scelleur avant de verser la couche finale? |
| Pascal 6/21/2012 3:55:06 PM |
RE: Nu Lustre 55 Message: Merci Mark On a sabler un peu ce matin et on a rappliquer une deuxieme couche apres. Tout est ok!! A part quelques poussieres qui tombe sur le comptoir. On a pas fait de tente, on aurait peut etre du!! Le comptoir est en Fibro-ciment, ca va etre super beau!!! |
| Mark 6/21/2012 4:02:56 PM |
RE: Nu Lustre 55 Message: Je suis très heureux que le Nu-Lustre a bien fonctionné . SVP envoyer quelques photos à moi. J'aimerais le voir. |
| Pascal 6/21/2012 5:20:18 PM |
RE: Nu Lustre 55 Message: Mark.. On lave le comptoir avec quoi un coup que tout sera sec? |
| Mark 6/21/2012 5:32:25 PM |
RE: Nu Lustre 55 Message: Attendre au moins 24 heures avant de places des choses sur la surface. Le Nu-Lustre prendra 30 jours d'être complètement dûr. Après 30 jours, vous pouvez employer les nettoyeurs sans abrasifs. |
| Pascal 6/22/2012 9:45:41 PM |
RE: Nu Lustre 55 Message: Bonjour Mark Est-ce que je peux rajouter un produit pour prevenir les egratignures (scratches) sur mon comptoir?? |
| Pascal 6/22/2012 10:19:21 PM |
RE: Nu Lustre 55 Message: Rebonjour J'ai fait des recherches sur votre forum et vous parlez pour prevenir les égratignures du produit antiquax marble wax. Est-ce un produit non-toxique pour les aliments? Car c'est pour un comptoir de cuisine!!! |
| Mark 6/23/2012 6:09:23 AM |
RE: Nu Lustre 55 Message: Antiquax Marble Wax prevenir les etratignures, et ce produit est non-toxique en sechant. |
| Laurence 7/19/2012 10:13:02 AM |
RE: Nu Lustre 55 Message: I want to pour a 16 foot counter top off site. The counter will flex in transportation. Will the finish crack when flexed? |
| Erick 1/12/2013 12:26:59 AM |
RE: Nu Lustre 55 Message: My situation is almost identical to Nicole''s a few posts up, what was the end recommendation for her problem? To quote her, "If I understand correctly I should: 1. Scrape out sticky spots 2. Use an epoxy thinner to clean out the spots (I''''m worried that it will also take off the paint on the bar underneath) 3. Sand off the dust from the hardened areas 4.Clean the entire room and surface 5. Make a trench 6. Re-pour" Is that the correct solution or is there another way to handle the problem? Thanks, Erick |
| Mark 1/14/2013 8:52:43 AM |
RE: Nu Lustre 55 Message: Nicole's pour was a real mess. She tried to spread the Nu-Lustre too thin and ended up with a surface that was not uniform. As well, some of the mixed batches were not done correctly, so there were also sticky spots. If you can send pictures I can give a better assessment. |
Post a reply to this message:
  |